品读常州NSK轴承压力与事后处理

对于常州NSK轴承的压入安装很多人都不陌生，但如何处理事后确是一个**难问题，今天我们就来解决这个**难问题。

Changzhou NSK bearings for the pressure of the installation of many people are not strange, but how to be a director is a difficult problem, today we come to solve the problem.

首先，压力需要匹配到位。根据公式可以计算出所需压机的吨位。其次，选择合适的工具来匹配压力机的压力头和轴承部件。通常，套筒零件总是与轴承部件接触。较后，这也是较重要的步骤之一。压力应直接应用在需要克服干扰力的部件上。例如，如果内圈有干涉条件，则内圈和滚道不能通过内圈将力传递到内圈，这将对轴承滚道造成损伤。

First, the pressure needs to be matched in place. According to the formula, the tonnage of the required press can be calculated. Secondly, choose the right tools to match the pressure head and bearing parts of the press. Generally, sleeve parts always contact with bearing parts. Finally, this is one of the most important steps. Pressure should be directly applied to components that need to overcome disturbance. For example, if the inner ring has interference conditions, the inner race and raceway can not transmit the force to the inner race through the inner race, which will cause damage to the bearing raceway.

常州NSK轴承后装检验与双保险

Changzhou NSK bearing rear loading inspection and double insurance

无论采用何种安装方法，安装后的检查都可以避免由于某些步骤的疏忽而导致轴承加载失败。例如，大型轴承的加热和安装后，由于热胀冷缩的影响，当温度降低时，轴肩附近的位置会产生一定的间隙。在计算分析中，这种差距是不存在的。加热装置通常需要采用连续的夹紧力来消除冷却过程中的间隙。这是为了纠正通过安装后检查纠正的典型场景安装不当。

No matter what installation method is adopted, the inspection after installation can avoid the failure of bearing loading due to the negligence of some steps. For example, after the heating and installation of large bearings, due to the influence of thermal expansion and cold contraction, when the temperature decreases, there will be some gaps in the position near the shaft shoulder. In computational analysis, this gap does not exist. Heating devices usually need continuous clamping force to eliminate gaps in cooling process. This is to correct improper installation of typical scenes after checking after installation.

如果按常州NSK轴承压入安装，如果肩关节的角半径太大**过轴承的圆角、后负荷检查成为必要的过程中找到纠正如压力输入不当的问题，加工误差，前序泄漏检测等等。

If the Changzhou NSK bearing is pressed into the installation, if the angular radius of the shoulder is too large to be more than the round angle of the bearing, the back load check becomes necessary to correct the problem of improper pressure input, processing error, presequence leakage detection and so on.

以上是轴承安装方法的一般概述。由于轴承种类繁多，用途广泛，安装规则和注意事项也各不相同。欢迎您就近咨询铁姆肯公司工程技术*。我们将用丰富的知识和技术解决各种问题。相信通过掌握正确的轴承安装方法，可以有效地减少轴承故障，提高设备的运行效率。

The above is a general overview of the method of bearing installation. Because of many kinds of bearings and wide uses, installation rules and matters needing attention are also different. You are welcome to consult The Timken Company engineering and technology expert. We will solve all kinds of problems with rich knowledge and technology. I believe that by grasping the right bearing installation method, we can effectively reduce the bearing failure and improve the operation efficiency of the equipment.




文章来自：常州SKF轴承 
The article comes from: Changzhou SKF bearing 
文章来自：常州INA轴承 
The article comes from: Changzhou INA bearing 
文章来自：常州NSK轴承 
The article comes from: Changzhou NSK bearing